Serialio

SUPPORT

Save RS3x Settings

You want to save the idChamp RS3x RFID reader NFC profile configuration settings to load on another RS3x. First load the RS3 NFC Setup App to your Android device. You can get this app on Google Play. Open the RS3 NFC Setup app and use menu, then Select Device, and select the RS3 to connect the RFID reader. After connected, you select NFC2, NFC3, NFC4 from the app drop-down. After each selection wait for the reading of each profile to complete before you select the next one. Finally, tap menu

Read More »

RS3x DIP Switch Settings for BLE Mode

You can set idChamp® RS3x RFID-NFC reader DIP switch settings for different operating modes. This page shows how to setup the RS3x DIP switch settings for BLE mode. You setup RS3x RFID engine using the RS3 NFC Setup iOS app. In addition, you setup RS3x RFID engine using the RS3 NFC Setup Android app. Note: the RS3x model RFID-NFC reader switch settings differ from the RS3 model. See here for RS3x DIP switch settings in cabled mode. DIP Switch Setting Images For BLE Mode DIP switch S3 and S5 settings

Read More »

RS3x DIP Switch Settings for Cabled Mode

You can set idChamp® RS3x RFID-NFC reader DIP switch settings for different operating modes. First, you can setup RS3x RFID engine using the RS3 NFC Setup iOS app. In addition, you can setup RS3x RFID engine using the RS3 NFC Setup Android app. Finally you can use cabled mode to setup the RFID-NFC engine with a Windows PC. For cabled mode, a USB RS-232 adapter is needed, along with an idChamp bridge cable. Additionally, you use the RS3x in cabled mode to read smart card badges with Windows PCs and

Read More »

idChamp RFID Readers Facilitate Mining Site Compliance

How does the 2nd largest major mining company in North America manage their on-site personnel?idhamp RFID readers facilitate mining site compliance at this major mining company. Why Tracking On-Site Personnel Is Important Knowing your employees locations is important for their safety. Additionally your contractors, visitors and guests also appreciate your concern for their safety. Finally your government likely requires compliance of your personnel management system. Multi-Site Personnel Management Problem How do you rate your company’s mining site personnel management?Your site compliance system must be able to report who is currently

Read More »

How to use the RS3 NFC Setup app for iOS to setup the idChamp RS3

This support article will walk you through how to use Serialio’s RS3 NFC Setup application for Android to configure your idChamp RS3. If you do not have access to an Android device, you can also configure your idChamp RS3 with the RS3 NFC Setup application for iOS or pcProx Configuration Utility for Windows. idChamp RS3-HSE Diagram DIP Switch Orientation   1 2 3 4 5 6 S2 Down Down Up Up Down Down S3 Up Up Down Down     S4 Down Up Down Up     S5 Down Down

Read More »

How to use the RS3 NFC Setup app for Android to setup the idChamp RS3

This support article will walk you through how to use Serialio’s RS3 NFC Setup application for Android to configure your idChamp RS3. If you do not have access to an Android device, you can also configure your idChamp RS3 with the RS3 NFC Setup application for iOS or pcProx Configuration Utility for Windows. idChamp RS3-HSE Diagram DIP Switch Orientation   1 2 3 4 5 6 S2 Down Down Up Up Down Down S3 Up Up Down Down     S4 Down Up Down Up     S5 Down Down

Read More »

How to configure the idChamp RS3 for BLE mode (units built after August 2019)

NOTE: These instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small tool for changing the DIP switches. In order to access all DIP switches, you’ll need to remove the outside case entirely. You can do this by removing the lid, turning the unit over, and gently tapping

Read More »

How to configure the idChamp RS3 for BLE mode (units purchased before August 2019)

NOTE: These instructions are for units built BEFORE August 2019. These units will NOT have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small tool for changing the DIP switches. In order to access all DIP switches, you’ll need to remove the outside case entirely. You can do this by removing the lid, turning the unit over, and gently

Read More »

How To Setup idChamp® RS3x Switches

The idChamp® RS3x RFID-NFC reader is a wireless BLE device. With optional HID firmware, it can optionally work in Bluetooth HID mode. Instructions Power off your RS3, remove the four lid screws, then remove the lid. Locate switches S3, S5. Use a small plastic device to change the switch settings if needed.   1 2 3 4 5 6 S3 ON ON OFF OFF N/A N/A S5 OFF ON ON OFF OFF ON   1 2 3 4 5 6 S3 ON ON ON OFF N/A N/A S5 OFF ON

Read More »

How to put a battery-powered idChamp RS3 in ‘Always On’ mode (units built after August 2019)

NOTE: These instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for ‘Always On’ mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small tool for changing the DIP switches. In order to access all DIP switches, you’ll need to remove the outside case entirely. You can do this by removing the lid, turning the unit over, and gently

Read More »