Serialio

RFID Readers

Sending Wireless Bluetooth Data Using 3rd Party Keyboard SerialMagic Keys

How can iOS keyboard be used to send user specified data to a wirelessly connected device?  SerialMagic Keys iOS provides a ‘Command Key’ option to send user defined data to trigger some event on the device connected to BlueSnap M6A DB9 connector serial port e.g. to trigger scale to send weight, RFID reader to read …

Sending Wireless Bluetooth Data Using 3rd Party Keyboard SerialMagic Keys Read More »

How to setup the idChamp 1126/1128 with SerialMagic Professional for Windows

This support article will show you how to configure SerialMagic Professional for Windows for use with the idChamp UHF 1126/1128. This tutorial is applicable to both the idChamp UHF 1126 desktop scanner and the idChamp UHF 1128 scanner. 1. Plug your idChamp 1126/1128 into your Windows PC via the micro USB cable that came with …

How to setup the idChamp 1126/1128 with SerialMagic Professional for Windows Read More »

How to use the RS3 NFC Setup app for iOS to setup the idChamp RS3

This support article will walk you through how to use Serialio’s RS3 NFC Setup application for Android to configure your idChamp RS3. If you do not have access to an Android device, you can also configure your idChamp RS3 with the RS3 NFC Setup application for iOS or pcProx Configuration Utility for Windows. idChamp RS3-HSE …

How to use the RS3 NFC Setup app for iOS to setup the idChamp RS3 Read More »

How to use the RS3 NFC Setup app for Android to setup the idChamp RS3

This support article will walk you through how to use Serialio’s RS3 NFC Setup application for Android to configure your idChamp RS3. If you do not have access to an Android device, you can also configure your idChamp RS3 with the RS3 NFC Setup application for iOS or pcProx Configuration Utility for Windows. idChamp RS3-HSE …

How to use the RS3 NFC Setup app for Android to setup the idChamp RS3 Read More »

How to configure the idChamp RS3 for BLE mode (units built after August 2019)

NOTE: These instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small tool …

How to configure the idChamp RS3 for BLE mode (units built after August 2019) Read More »

How to configure the idChamp RS3 for BLE mode (units purchased before August 2019)

NOTE: These instructions are for units built BEFORE August 2019. These units will NOT have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small …

How to configure the idChamp RS3 for BLE mode (units purchased before August 2019) Read More »

How To Setup idChamp® RS3x Switches

The idChamp® RS3x RFID-NFC reader is a wireless BLE device. With optional HID firmware, it can optionally work in Bluetooth HID mode. Instructions Power off your RS3, remove the four lid screws, then remove the lid. Locate switches S3, S5. Use a small plastic device to change the switch settings if needed.   1 2 …

How To Setup idChamp® RS3x Switches Read More »

How to put a battery-powered idChamp RS3 in ‘Always On’ mode (units built after August 2019)

NOTE: These instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for ‘Always On’ mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small …

How to put a battery-powered idChamp RS3 in ‘Always On’ mode (units built after August 2019) Read More »

How to connect the Scanfob NFC-BB2 to SerialMagic Professional for Windows with the BlueSnap USB

This article provides instructions on how to pair the Scanfob NFC-BB2 with SerialMagic Professional for Windows with the BlueSnap USB dongle. 1. Launch SerialMagic Professional. 2. If this is not your first time launching the SerialMagic Pro application, click “Add.” 3. Select “Connect to the remote Bluetooth device using BlueSnap USB.” 4. Select the image …

How to connect the Scanfob NFC-BB2 to SerialMagic Professional for Windows with the BlueSnap USB Read More »