Serialio

idChamp RS3x

How to use the RS3 NFC Setup app for iOS to setup the idChamp RS3

This support article will walk you through how to use Serialio’s RS3 NFC Setup application for Android to configure your idChamp RS3. If you do not have access to an Android device, you can also configure your idChamp RS3 with the RS3 NFC Setup application for iOS or pcProx Configuration Utility for Windows. idChamp RS3-HSE …

How to use the RS3 NFC Setup app for iOS to setup the idChamp RS3 Read More »

How to use the RS3 NFC Setup app for Android to setup the idChamp RS3

This support article will walk you through how to use Serialio’s RS3 NFC Setup application for Android to configure your idChamp RS3. If you do not have access to an Android device, you can also configure your idChamp RS3 with the RS3 NFC Setup application for iOS or pcProx Configuration Utility for Windows. idChamp RS3-HSE …

How to use the RS3 NFC Setup app for Android to setup the idChamp RS3 Read More »

How to configure the idChamp RS3 for BLE mode (units built after August 2019)

NOTE: These instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small tool …

How to configure the idChamp RS3 for BLE mode (units built after August 2019) Read More »

How to configure the idChamp RS3 for BLE mode (units purchased before August 2019)

NOTE: These instructions are for units built BEFORE August 2019. These units will NOT have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small …

How to configure the idChamp RS3 for BLE mode (units purchased before August 2019) Read More »

How To Setup idChamp® RS3x Switches

The idChamp® RS3x RFID-NFC reader is a wireless BLE device. With optional HID firmware, it can optionally work in Bluetooth HID mode. Instructions Power off your RS3, remove the four lid screws, then remove the lid. Locate switches S3, S5. Use a small plastic device to change the switch settings if needed.   1 2 …

How To Setup idChamp® RS3x Switches Read More »

How to put a battery-powered idChamp RS3 in ‘Always On’ mode (units built after August 2019)

NOTE: These instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for ‘Always On’ mode, follow the instructions below.  You’ll need a Phillips head screwdriver and a paper clip or small …

How to put a battery-powered idChamp RS3 in ‘Always On’ mode (units built after August 2019) Read More »

How to retrieve device information with yACK BLE for iOS

This support article demonstrates how to retrieve device information (in this case, we are retrieving information from the idChamp RS3 by using the yACK BLE app for iOS to send the get al command. The yACK BLE application is also available on Android.  1. First, make sure that the device is in BLE mode. The yACK BLE application only works with …

How to retrieve device information with yACK BLE for iOS Read More »

How to remove idChamp RS3 keystroke delimiters on iOS

This support article demonstrates how to remove keystroke delimiters from the idChamp RS3 Dual Engine RFID Reader with the RS3-NFC Setup application for iOS. This tutorial assumes that you have already installed the RS3-NFC Setup application for iOS. If you have not already done so, please do so now. Adjust the DIP Switches for BLE Mode You must …

How to remove idChamp RS3 keystroke delimiters on iOS Read More »