NOTE: RS3 Has been discontinued. See the RS3x These instructions are for RS3 units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5. RS3 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below. You’ll need a Phillips […]
Setup idChamp RS3 BLE mode (Post August 2019) Read More »
NOTE: This product is discontinued. See the RS3xThese instructions are for units built BEFORE August 2019. These units will NOT have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for BLE mode, follow the instructions below. You’ll need a Phillips head screwdriver
Setup idChamp RS3 BLE mode (Pre August 2019) Read More »
The idChamp® RS3x RFID-NFC reader is a wireless BLE device. With optional HID firmware, it can optionally work in wireless HID mode. Instructions Power off your RS3x, remove the four lid screws, then remove the lid. Locate switches S3, S5. Use a small plastic device to change the switch settings if needed. Note: Image below
How To Setup idChamp® RS3x Switches Read More »
NOTE: RS3 Has been discontinued. See the RS3xThese instructions are for units built after August 2019. These units will have a white UART connector on the PCB board next to banks S4 and S5 Getting Started To prepare your idChamp RS3 for ‘Always On’ mode, follow the instructions below. You’ll need a Phillips head screwdriver and
Set Battery-Unit idChamp RS3 in ‘Always On’ Mode (Post August 2019) Read More »
This support article demonstrates the configuration settings required to accurately read iClass cards of various bit counts. If you are using or planning to use the idChamp RS3 with iClass cards with a bit count other than 26, this article is for you. To accurately read cards with bit counts other than 26, you need to
How to configure the idChamp RS3 to read a specific bit count Read More »
This article demonstrates how to switch Bluetooth modes on the Scanfob qID mini UHF reader. Note: The Scanfob qID must be unpaired from any devices before switching the Bluetooth mode. 1. Access the main menu by holding down the scan button within two seconds of powering on the qID. There are four main menu options;
How to switch Bluetooth modes on the Scanfob qID Mini Read More »
This article is for customers using the idChamp A9 triggers with SerialMagic Gears to scan into another Android application. Follow the instructions below to learn how to enable this feature. Note: This feature is only available with SerialMagic Gears version 1.31.75 or later. If SerialMagic Keys is already enabled and set as your default keyboard, skip to
How to setup SerialMagic Keys to allow idChamp A9 triggers outside of SerialMagic Gears Read More »
Mobile Attendance Decoding Different RFID Badges There are many different ISO standards, protocols, and physical differences between various RFID tag types. Choosing compatible readers and tags can be tricky, especially for an RFID novice. For the purposes of this explanation, we’ll only focus on passive RFID, specifically, Low-Frequency (LF), High-Frequency (HF), Near Field Communication (NFC),
Pick RFID Reader & Badge for Mobile Attendance? Read More »
RFID Tags RFID tags consist of two primary components; a microchip that processes and stores the information/data and an antenna to receive and transmit RFID radio-wave signals. To read information from the tag/label, a two-way radio-receiver called an interrogator (or reader) sends a radio-wave signal to the tag(s) using its antenna. Tags that are within range
Many of our customers want to know just how secure Bluetooth Low Energy (BLE) — or Bluetooth Smart/Bluetooth 4.0 — communication is. In response, we’ve made this article to provide basic information about the BLE standard, what it entails and what it means for your security concerns. The BLE Pairing Process How does Bluetooth Low Energy pairing
Bluetooth Low Energy (BLE) Security Read More »